Glowshift Celsius Exhaust Gas Temperature Gauge User Manual download pdf

7 Color Series Celsius Pyrometer EGT Gauge

For Product Numbers: GS-C708-C, GS-T708-C, GS-W708-C

Wire Color Code

Yellow:

12v Constant Source (+) (un-switched)

Orange:

12v Switched Headlamp Source (+) (optional)

Red:

12v Ignition Source (+) (switched)

Blue:

Connects to the Blue Wire on the EGT Probe

Black:

Vehicle Ground ( - )

Pink:

Connects to the Pink Wire on the EGT Probe

1. Disconnect the vehicle's negative battery cable.

Installing the EGT Probe

2. There are two common types of EGT probe installations. We recommend

installing the probe pre-turbo for the most accurate reading.

 Exhaust Manifold: Drill and tap the exhaust manifold to 1/8

-27 NPT.

Install the supplied EGT probe directly into your exhaust manifold.

Note: After drilling and tapping your exhaust manifold be sure

to use both a magnet and vacuum to safely remove all shavings

from the manifold.

 Exhaust Temperature Bracket: This method is not shown, but you

may purchase an exhaust temperature bracket from

www.GlowShift.com. This adapter is clamped and tightened around the

exhaust pipe and provides a 1/8

NPT fitting for an EGT probe. Using a

3/16

drill bit, drill a hole in your exhaust pipe. Position and tighten the

adapter clamp, then permanently mount the probe through the fitting and

into the exhaust pipe.

Connecting the Power Wire Harness

3. To make the wiring of your gauges easier you can purchase an expandable

circuit. This component easily fits into your fuse panel and provides an

additional fused power wire for accessories such as gauges. The expandable

circuit is available for purchase at www.GlowShift.com.

4. Connect the pink & blue wires from the gauge wire harness to the pink &

blue wires of the exhaust temperature probe.

5. Using automotive grade wiring (18 gauge), connect the yellow wire to a

positive 12 volt constant (un-switched) source either on the vehicle or in the

fuse box.

 Note: If you are connecting the yellow wire directly to the battery,

you MUST install a 3 amp fuse within 6-8 inches of the battery

connection.

6. Using automotive grade wiring (18 gauge); connect the red wire to a

positive 12 volt ignition (switched) source. It may be connected to the

fuse panel, an accessory wire, or any positive 12 volt source that turns

on and off with the ignition.

7. Using automotive grade wiring (18 gauge); connect the black wire to

any good (unpainted) ground connection. You may also route a wire

directly to the negative side of the vehicle’s battery.

8. The Night Time Dimming feature decreases the brightness of the

gauge face by 30%. Connect the orange wire to the 12 volt positive

headlamp source. This allows the mode to be activated when the

headlights come on. This step is optional and will not affect operation

of the gauge if it is omitted.

 Note: Do not connect the orange wire to a dimmer wheel.

This will cause the gauge lighting to flicker.

9. Reconnect the vehicle's negative battery cable.

 If your gauge(s) do not illuminate or do not recall your last

saved color, your switched and un-switched sources are

reversed.

 If your gauge(s) only illuminate red then the yellow wire for

constant source is not connected properly.

 Be sure all of your wiring is correct to ensure proper gauge

operation.

1 2 3

Summary of Contents

Page 1

7 Color Series Celsius Pyrometer EGT Gauge For Product Numbers: GS-C708-C, GS-T708-C, GS-W708-C Wire Color Code Yellow: 12v Constant Source (+) (u

Page 2

Additional Installation Information & Material Requirements  GlowShift Gauges Approved Conductor Wires: Successfully installing GlowShift Gaug

Page 3

3. EXCEPTIONS TO LIMITED WARRANTY: GlowShift shall have no obligation to Purchaser with respect to any Product that is subjected to any of the fo

Comments to this Manuals

No comments

Glowshift Celsius Exhaust Gas Temperature Gauge User Manual

Browse online or download User Manual for Accessories for water Glowshift Celsius Exhaust Gas Temperature Gauge. GlowShift Celsius Exhaust Gas Temperature Gauge User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for water Glowshift Celsius Exhaust Gas Temperature Gauge