Glowshift Wideband Air / Fuel Ratio Gauge w/ Datalogging Out User Manual download pdf

Tinted Series Wideband Air/Fuel Ratio Gauge

For Product Numbers: GS-T02W

Wire Harness Color Code

Red:

12v Constant Source (+) (

un-switched

)

Black:

Vehicle Ground ( - )

White:

12v Ignition Source (+) (

switched

)

Orange:

12v Switched Headlamp Source (+) (

optional

)

Disconnect the negative battery cable.

2. Mount the controller inside the vehicle away from heat,

water, moisture, dirt and all moving parts, in an easily

accessible location. This allows for the unit to be accessible

should calibration need to be performed.

3. Install the provided LSU 4.9 Sensor by welding the

matching exhaust bung to the exhaust pipe.

 Note: We recommend using Anti-Seize on the bung

threads so that you can unscrew the sensor when

necessary.

 Make sure the location of the bung is no less than a

minimum of 6 inches after the exhaust ports, but

before the catalytic converter, and no more than 36

inches from the last exhaust port.

 The bung must be installed to the top or side of the

exhaust pipe at a minimum of 10 degrees for the top

and 15 degrees for the side from a horizontal

position with the electrical connection up to prevent

a collection of liquid at the element during the warm

up phase.

Next, route and secure the sensor wire harness from the sensor

into the vehicle, close to the controller’s location. Be sure to

use a grommet when routing the wires through the firewall to

protect them from stripping.

5. Connect the red wire to a positive 12 volt constant (un-

switched) source either directly to the battery or to a fuse panel

on the vehicle. If wiring to an un-fused source, install a 3 amp

fuse inline within 20 inches of the sources connection.

6. The white wire should be connected to a positive 12 volt

ignition (switched) source. It may be connected to the fuse panel,

an accessory wire, or any positive 12 volt source that turns on and

off with the ignition

7. Connect the black wire to any good (unpainted) ground

connection. You may also route a wire directly to the negative side

of the vehicle’s battery.

8. The Night Time Dimming feature decreases the brightness of the

gauge face by 30%. Connect the orange wire to the 12 volt

positive headlamp source. This allows the mode to be activated

when the headlights come on. This step is optional and will not

affect operation of the gauge if it is omitted.

 Note: Do not connect the orange wire to a dimmer wheel.

This will cause the gauge lighting to flicker.

9. Reconnect the negative battery cable.

1 2 3

For Product Numbers: GS-T02W 1

Summary of Contents

Page 1 - For Product Numbers: GS-T02W

Tinted Series Wideband Air/Fuel Ratio Gauge For Product Numbers: GS-T02W Wire Harness Color Code Red: 12v Constant Source (+) (un-switched) Black:

Page 2

Calibration Schedule Prior to calibration remove the sensor from the bung. This will ensure a proper calibration. To obtain the most accurate resu

Page 3

ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER GlowShift Gauges, LLC ("GlowShift") warrants to the original retail consumer p

Comments to this Manuals

No comments

Glowshift Wideband Air / Fuel Ratio Gauge w/ Datalogging Out User Manual

Browse online or download User Manual for Accessories for water Glowshift Wideband Air / Fuel Ratio Gauge w/ Datalogging Out. GlowShift Wideband Air / Fuel Ratio Gauge w/ Datalogging Output User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for water Glowshift Wideband Air / Fuel Ratio Gauge w/ Datalogging Out